Please confirm topic selection

Are you sure you want to trigger topic in your Anconeus AI algorithm?

Please confirm action

You are done for today with this topic.

Would you like to start learning session with this topic items scheduled for future?

Cervical Myelopathy
Updated: Oct 4 2016

Posterior Cervical Laminectomy and Fusion

Preoperative Patient Care
Operative Techniques
E

Preoperative Plan

1

Radiographic templating

  • template screw size and levels of fusion

2

Execute surgical walkthrough

  • describe the steps of the procedure to the attending prior to the start of the case
  • describe the potential complications and steps to avoid them
F

Room Preparation

1

Surgical instrumentation

  • Loupes or operating microscope
  • jackson table with flat board and four post frame
  • gardner wells tongs with 20 lbs of traction
  • insulated and bipolar cautery
  • angled cerebellar retractors
  • high speed burr with non end cutting drill attachment
  • multiple angled curets
  • kerrison rongeurs 1-3 mm
  • lateral mass and pedicle fixation screws

2

Room setup and equipment

  • standard operating table with Gardner-Wells tongs
  • use 15lbs of traction
  • fluoroscopy

3

Patient positioning

  • prone
  • position neck in slight extension with neutral rotation
G

Dissect to Spinous Process

1

Determine level of instrumentation

  • use fluoroscopy to determine the level of fusion

2

Make skin incision

  • incise through the skin and subcutaneous tissues
  • cauterize bleeders as they occur

3

Expose the cervical fascia

  • incise in the midline
H

Clear Lamina and Lateral Masses

1

Perform a subperiosteal dissection

2

Expose the lateral recess

3

Confirm the surgical level

  • use the C2 vertebra as the starting point and count down from there
  • place a penfield 4 elevator into the facet joint
I

Placement of Lateral Mass Screws

1

Identify starting point

2

Drill pilot holes for all levels

  • use a 2mm burr to make a small depression in the lateral mass that is 1 mm medial to the center.
  • this is done to identify a starting point for the drill bit
  • place a drill stop set at 12 or 14 mm depending on the size of the lateral mass
  • place the drill onto the starting point and drill a tract with the drill angled 30 degrees lateral and 15 degrees cephalad
  • these are drilled for placement of the lateral mass screws

3

Confirm the tract

  • place a ball tipped probe into the tract to confirm its integrity

4

Place screws

  • tap each screw tract to the same depth that was drilled
  • place 3.5 mm screws of the appropriate length

5

Confirm position using fluoroscopy

J

Laminectomy

1

Create laminar troughs

  • create troughs in the lamina bilaterally just medial to the lateral massses
  • using a non end cutting burr because the likelihood of injury to the underlying dura and spinal cord are decreased
  • stop drilling frequently and use a penfield 4 elevator to check the depth of the trough
  • continue this process until the ligamentum flavum is visualized

2

Remove ligamentum flavum

  • use a nerve hook to elevate the flavum
  • resect the flavum using a 2 mm kerrison rongeur

3

Elevate lamina

  • use leskell rongeurs to grab to the cephalad and caudad levels
  • constant pressure should be applied to and maintained on the lamina so that no compression on any part of the cervical spinal cord occurs
  • tease off any adhesions on the lamina

4

Check motor evoked potentials

5

Check mean arterial pressure

  • this must be maintained to avoid ischemic injury to the cord

6

Elevate the lamina

  • use angled curets and elevate the lamina sequentially from distal to proximal in an EN BLOC fashion
K

Place C7 Pedicle Screw (if required)

1

Perform laminoforaminotomy at C6-C7

  • use a 2-3 mm burr to create a starting point at the intersection of the midpoint of the transverse process and the lateral pars
  • this is done so that the medial border of the pedicle can be visualized and palpated
  • look for a pedicle blush which signifies the cancellous bone

2

Make screw tract

  • use a pedicle awl or gearshift to to make the tract within the pedicle
  • palpate the medial border of the of the pedicle
  • this can assess the medial-lateral and cranio-caudal angulation of the pedicle
  • palpate the medial border of the of the pedicle
  • place a ball tipped probe to confirm the tract
  • tap the tract

3

Place C7 screws

  • place 4.0 mm screws of the appropriate length bilaterally
L

Fusion and Rod Placement

1

Decorticate

  • use a high speed burr to decorticate the facet joints and the lateral aspects of the lateral masses

2

Use local bone from the laminectomy for biologic arthrodesis

3

Place Rods

  • place the end caps
  • place the appropriately sized rods into the screw heads
  • perform a final tightening of the instrumentation
N

Wound Closure

1

Irrigation, hemostasis, and drain

  • place subfascial drain
  • obtain muscular hemostasis

2

Deep closure

  • use 0 or 1 absorbable suture
  • close the muscle and fascia in separate layers

3

Superficial closure

  • subcutaneous tissue is closed with 2-0 vicryl
  • close skin with buried monocryl

4

Dressing and immediate immobilization

  • place bulky dressing and soft collar
Postoperative Patient Care
Private Note

Attach Treatment Poll
Treatment poll is required to gain more useful feedback from members.
Please enter Question Text
Please enter at least 2 unique options
Please enter at least 2 unique options
Please enter at least 2 unique options